Recording a web routine means turning supported interactions into steps that can be reviewed and replayed. In Tapper’s upcoming update, you can record actions in the built-in browser, inspect the resulting sequence, adjust its timing, and save it for another session.
This is different from recording a video of your screen. A video preserves what happened visually; a routine contains instructions the app will try to perform again. It also differs from recording every gesture across iOS. Tapper’s routines operate on supported webpages, not inside unrelated native apps.
Choose a small task to record
Pick a short, reversible task with an obvious result. A practice counter is a good first example because each successful tap changes a visible number. A long sequence involving login, navigation, forms, and changing content is harder to diagnose.
Before recording, write a one-sentence goal: “Tap the first practice button twice.” Then identify the starting state: the page is open, the counter is reset, and the button is visible. A reusable routine needs both a sequence and a predictable place to begin.
If your task requires multiple targets, first read the multiple-point setup guide. Recording is a convenient way to create steps, but it does not remove the need to understand their order.
Record the actions
- Open the supported webpage in Tapper’s browser.
- Put it in the state where the routine should begin.
- Choose Record.
- Perform the small sequence you want to capture.
- Choose Finish recording to end the recording.
- Review the resulting steps before running them.
Do only the intended task while recording. Extra taps, exploratory scrolling, or opening controls can make the resulting sequence harder to interpret. If you make a mistake, it is often easier to record a short clean sequence again than to untangle a large one.
Some website interactions may not translate into supported routine steps. An embedded frame, a canvas, or a control that depends on a trusted human gesture can behave differently. Review what was actually recorded instead of assuming every visible interaction was captured perfectly.
Read the recording as instructions
Open Edit routine and inspect each step. Ask what it targets, how long it waits, and what needs to be true before it runs. A tap on a button that appears only after loading needs a different setup from a tap on a static practice counter.
Remove accidental actions and correct the order where needed. Review the delay before each step. Your timing during the original recording may include a moment of hesitation or may be too quick for a later, slower page load. A recording is a draft, not automatically a reliable final routine.
If the webpage provides a stable element target, selecting that element can be more resilient than relying only on a screen position. It is not foolproof: the element still needs to exist and remain the intended control. The target-selection comparison explains that distinction.
Replay once before adding a loop
Restore the original starting state before the first replay. Return to the correct page, close the same overlays, and make sure the same button is visible. If the recording changed a counter or opened a panel, undo that change manually where appropriate.
Set one repetition for the first test. Watch each step and compare the final webpage state with your intended result. If the routine has two taps, one repetition means running those two taps once; setting ten repetitions may request twenty tap actions.
When a step fails, stop and inspect it. Do not use a larger repeat count to compensate for a missed target. The missed-tap article gives a practical way to separate target movement from timing problems.
Adjust timing and waits
Use a delay when the next action simply needs a fixed pause. Use an available wait condition when the next action depends on the webpage reaching a particular state. A page-load wait and a text wait answer different questions, so choose the one that matches the actual dependency.
For example, a page may finish loading before a result label appears. Waiting for that label, with an appropriate timeout, can express the task more accurately than choosing an arbitrary long delay. The label must be stable and specific enough to identify the intended state.
Waits also need endings. If the expected condition never appears, the routine should time out rather than assume success. Learn more in the wait-step explanation.
Save with a useful name
Once a short replay works, save the routine with a name that identifies its task and scope. “Practice — two taps” is clearer than “Test.” For real pages, include the relevant section or intended result without putting private account information into the name.
When you reuse the routine later, review it against the current website. A saved routine does not preserve the server, account session, or page design. Website changes can require retargeting, a different wait, or a new starting URL.
Recording, advanced saved routines, and advanced replay are part of the upcoming premium feature set, with three shared preview runs before an upgrade is needed. Review the free and premium explanation and the offer shown inside your installed version.
Keep the final result in view
A successful routine is one that does the intended job, not merely one that reaches its last step. Check the webpage’s visible result after replay and compare it with the run information. Keep the app open during the session and stop before leaving the task.
The screenshots here preview the unreleased 1.0.6 redesign. The current App Store build may show different controls. Download Tapper through the official listing, check the available version, and use practice to learn the behavior before moving to a third-party webpage.
A good routine starts small.
Open the official App Store listing, check the available version, and try a supported webpage.
Download for iPhone